Ford Programming Instructions
Ford Keyless remote programming (sometimes called installation) and activation is a simple process. Actually, despite of the common name - remote programming, the process involves training the vehicle to recognize a new keyfob you purchased. You really do not program a fob, but rather train the vehicle to learn or recognize a new wireless unit.FREE FORD REMOTE PROGRAMMING INSTRUCTIONS1) Turn ignition from OFF to RUN (as far as you can go without cranking the engine) 8 times (one turn is from OFF to RUN and back to OFF) within 10 seconds, with the 8th time ending in RUN (8th time you only go from OFF to RUN and stop there) ( do not start the engine).2) All doors will lock then unlock to confirm programming mode.3) Within 20 seconds, press any button on 1st car remote transmitter. Door locks will cycle to confirm remote programming.4) Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible).
You have to press a button on every remote you have, including all the working original remotes if avail.5) Turn ignition to OFF. Keyless Remotes for CarsKeyless remotes for cars are electronic controls for vehicles that perform the same functions as a key, except that you only have to push a button instead of actually having to put a key into the lock. Keyless remotes come in the form of a key fob or are integrated into the vehicle key's handle.What do keyless remotes do?Some types of keyless remotes for cars can actually start your vehicle for you, as well as unlocking or locking doors, opening the trunk, etc.
These devices are just about standard on most cars these days, and were first seen in the U.S. In 1989, on select General Motors vehicles. They normally get their power from batteries inside the remote.Today's models also have buttons to let you open and close windows, or have a panic button that can set off an alarm if the driver has a problem. There are even car models that have a special sensor in the keyless remote that prevents you from accidentally locking your keys in the car!How do keyless remotes work?The way they work is by sending a radio signal to a receiver located in the vehicle that activates the lock or other device and makes it function. The original keyless remotes worked by infrared signal until it was switched over to a radio signal.Security is indeed a huge issue when it comes to keyless remotes for cars, because if someone could open cars other than their own with their remote, then they could easily steal someone's vehicle. To foil this possibility, these keyless remotes are also encrypted, so that a car thief can't trick the vehicle into starting or opening by other means than the legitimate keyless remote.If a car owner loses his keyless remote, he will have to buy one made for his vehicle and get it re-coded and set to work with his car or truck.
Due to the special needs of each keyless remote to be able to work with a specific vehicle, they are expensive to replace and usually cost more than $100 for each key or fob.Each vehicle will have its own codes so that people can't just get into another person's vehicle with the same brand of keyless remote. On occasion, the owner may have to reprogram an old remote if they changed the batteries and somehow managed to cause it to dump all of the information that was stored on it.There have been limited timeframes in the past when outside signals would cause a car's keyless remote to stop functioning due to some sort of interference, but the remotes of today are more sophisticated and that seldom happens with newer remotes.
They are considered to be very convenient by all car and truck owners.The bottom line is that today, most cars and trucks have the convenience of a keyless remote to operate many of its components from the windows, trunk, lights and doors, and in some cases even starting up the engine so that you can stay warm on chilly mornings while your car's interior and engine warm up. CAR REMOTES BY MAKE.
Coding a New Ford Remote – Coding Machine Is RequiredMost of Ford models made in the past 20 years are equipped with some sort of transponder security feature.That security feature requires an additional action (programming the key) to start the car.Either a locksmith or a dealer can program the key for you if you choose to.However, the car will have to be towed there.Alternatively, for some models, you can do it yourself. The instruction below shows you how to program the new key yourself without any special equipment or help from an outside source. Click To Order OnlineIMPORTANT:Programming a new key when you do not have a working key only possible for Models with a PATS1 system. (Here is the list of models that have PATS1 system: Ford Contour 97-98, Expedition 97-98,(optional transponder), Mustang 96-97(optional transponder), Mystique 97-2000 optional transponder), Navigator 1998, Sable 96-97(optional transponder), Taurus 96-97.The most common keys that PATS1 uses are H72-PT and H73PT. The rest of the transponder keys are for PATS2-5.Adding a duplicate or creating an additional key is possible for all models.A step by step on how to program a new Ford key when all keys are lost, troubleshooting, what you should know and more. High Security Ford Transponder Key – Needs To Be ProgrammedSome Ford models can be programmed without any special machine. Those models are equipped with a security system called PATS1.
Models that are equipped with security systems PATS2-5 require a special programming machine if all keys are lost.Therefore, if your car is equipped with a PATS1 system and you already have a cut key for any of these makes or models, you can program it yourself without calling a locksmith or tow the car to the dealer.Here we will give detailed instructions on how to program a new key, what you should pay attention to, troubleshooting and useful tips that can save you a lot of money and time.A few tips before you start the process of programming a new car key for Ford models: PATS1 ONLY! H72 – PT: This key used for PATS1 systems mostlyA. Once you program a new key, ALL previous keys will be erased and won’t start the car.In other words, if you find your old key after programming the new one, it will not work.Therefore, we highly recommend having at least two new cut keys and program them both.B. Programming Ford keys require about 50 minutes of battery life, without the car being on.Therefore, it is very important to make sure you have enough juice in the battery before starting the process. In case the battery dies during the process, the new master key will not program and you will have to start the procedure all over again.C. While Ford models with a PATS1 system can be programmed with this method, we would recommend verifying the type of key with a locksmith or an additional reliable source that it is the right key.D. There are a few transponder keys (H72-PT, H73-PT, H74-PT, H86-PT, H92-PT, H94-PT) that work on Ford models.
You must have the right type of transponder key that matches your model and year.Otherwise, the key will not program. You can check the right key for the exact make and model.E. Most H72-PT and H73-PT are used for PATS1 systems(older models, usually 96-99). The rest are used for PATS2-5 systems. Program Ford Keys – Procedure and Type Of Keys. Insert the new cut and unprogrammed key you have into the ignition cylinder and turn it to the “ON” position. Make sure you look at the dash as the security/theft light should flash as you turn the key.
Extract iso via network bates. I really do want to rip the ISO directly to my PC via the network, but now that the ISO2DSD link is dead, I cannot find the Extract ISO via Network.bat for the PC.
If the security light doesn’t illuminate it means you have a problem with your battery and you should charge or replace it. Once the security light flashes, it will stay on for fifteen minutes. We suggest you have a stopwatch as well because the next step will have to happen within three minutes and you don’t want to miss that.
After the first 15 minutes, the security light will stop flashing, within three minutes, you should turn the ignition cylinder into “OFF” position and then back to “ON” again. The security light on the dash should flash for an additional fifteen minutes and then go off. Within three minutes, turn the ignition cylinder into “OFF” position and then back to “ON” again. The security light on the dash should flash for an additional 15 minutes and then go off.
Once the security light goes off after the 3 rd time (total 45 minutes) the new key should be programmed and start the car. Keep in mind, ALL other keys will not work anymore. Now you can start the car.
We highly recommend making a copy of the key.Call Now. Click To Order OnlineI already have a working key, I just want to make a duplicate. Ford latest generation of remotes key fobs – Better security features – Coding is neededFord remote car keys, also known as key fobs, smart keys or push to start keys, are the latest generation of security car keys.Therefore, onboard programming or self-programming is not available for these type of keys or remotes and additional equipment or programming/coding machine is necessary to complete this process.An automotive locksmith or the dealer will have to connect this machine to the car’s computer and only then a duplicate or a new key can be made. Below, a few examples of Ford remote key fobs that require programming machine.
Car Key Programming Machine For Ford Remotes & Key FobsHow can I save money on getting a duplicate or a new Ford key/remote made?As we explained above, the process of getting a new key involves cutting the new key and program it.When you call a locksmith or the dealer, they will charge you for a service call, the actual key, the labor of cutting the key and programming.Fortunately, you can save the money of the key by ordering it online, and only have them cut and program it. This alone will save you about $50-$100 as the locksmith or the dealer make a profit by selling you the key as well.True, it may take a longer time to get the key from Amazon but if you are not in a big rush or need a key ASAP, we recommend you do that. This is especially true if you only need a duplicate made.
Bottom line, how and what should I do?. Order your key online – Make sure you get the right key.
In case you get the wrong key or remote programming will not be possible. You can look up your exact key for your Ford model. Simply choose your model and year and get it online. You can order your key. Call the dealer or locksmith – Explain to them you already have the key/remote and would only like it to be cut and/or programmed.
Ask them for the quote on this procedure only. In addition, keep in mind, the process usually cost somewhere between $80-$150, depends on the type of key/remote you have. Finally, schedule a time with them to have it done. Remember to provide them with the exact year, make and model, VIN number and make sure you have a proof of ownership.Call Now. Ford Key / Remote Programming CostProgramming a new Ford key, assuming you already have a blank key, basically involves two phases:1.
Ford Remote Start Programming Instructions
Cutting the key or remote so it will fit your car’s ignition.Before the key can be programmed, it needs to be cut to fit your car. The way an automotive locksmith or the dealership do that is by “pulling” the key code, using your VIN from the database. This cost them money and therefore, they charge you for it. (Unlike when you already have a cut key and just need a duplicate)2. Program the key or remote – To actually start the car.The programming procedure is simply a process to let your car know that the new key is “authorized” to start the car. That being done by connecting a programming machine to your car’s computer.Both the dealer and an automotive locksmith will have to do the same thing, however, the prices vary.
Ford Duplicate Key Cost – By Dealer & Automotive LocksmithAs stated above, some Ford keys for older models can be self-programmed. However, newer generation keys and remotes can only be programmed or duplicated with a programming machine.The price of making a duplicate Ford key is cheaper than making an original key when all keys are lost for two main reasons:.
Ford Key Programming Instructions
You already have a cut key – That means no need to “pull” code from the database. Your car’s computer already “knows” that one key is authorized to start the car and therefore we can use that key to add some more. (Note that not in all models and years it’s possible)Here is the average cost of getting a duplicate Ford key by the dealership and an automotive locksmith: Cost of duplicate a Ford key by the dealer:These are average costs, as it really depends on the year and model of your Ford car.Cutting the key: Usually around $10Programming the key: Usually around $100Total estimated cost: $110.